Roundup, 100 ml

Roundup is a post-emergent, systemic herbicide with no soil residual activity. It is generally non-selective and gives broad-spectrum control of many annual weeds, perennial weeds, woody brush, and trees. It is formulated as a water-soluble liquid. It may be applied through most standard industrial or field-type sprayers after dilution and thorough mixing with water or other carriers according to label instructions.

Treated plants:  Apple tree, Barley, Beans, Beet sugar, Corn, Flax, Leek, Mustard, Oat, Onion, Peas, Plumtree, Rapeseed, Rye, Sylviculture, Vineyard, Wheat

Combat weeds: Creeping thistle, Field bindweed, Goosegrass, Johnson grass

Roundup moves through the plant from the point of foliage contact to and into the root system. Visible effects on most annual weeds occur within 2 to 4 days, but on most perennial weeds may not occur for 7 days or more. Extremely cool or cloudy weather following treatment may slow the activity of this product and delay the development of visual symptoms. Visible effects are a gradual wilting and yellowing of the plant which advances to complete browning of above-ground growth and deterioration of underground plant parts.

MIXING
Clean sprayer parts immediately after using this product by thoroughly flushing with water.
NOTE: REDUCED RESULTS MAY OCCUR IF WATER CONTAINING SOIL IS USED, SUCH AS VISIBLY MUDDY WATER OR WATER FROM PONDS AND DITCHES THAT IS NOT CLEAR.

Mixing with Water: This product mixes well with water.

Mix spray solutions of this product as follows:

- Fill the mixing or spray tank with the required amount of water.

- Add the recommended amount of this product near the end of the filling process and mix well.

- Use caution to avoid siphoning back into the carrier source.

- Use approved anti-back-siphoning devices where required by state or local regulations. During mixing and application, foaming of the spray solution may occur.

- To prevent or minimize foam, avoid the use of mechanical agitators, terminate by-pass and return lines at the bottom of the tank and, if needed, use an approved anti-foam or defoaming agent.

Tank Mixing Procedure
Mix labeled tank mixtures of this product with water as follows:
1. Place a 20- to 35-mesh screen or wetting basket overflowing port.
2. Through the screen, fill the spray tank one-half full with water and start agitation.
3. If ammonium sulfate is used add it slowly through the screen into the tank. Continue agitation. Ensure that dry ammonium sulfate is completely dissolved in the spray tank before adding other products.
4. If a wettable powder is used, make a slurry with the water carrier, and add it SLOWLY through the screen into the tank. Continue agitation.
5. If a flowable formulation is used, premix one part flowable with one part water. Add diluted mixture SLOWLY through the screen into the tank. Continue agitation.
6. If an emulsifiable concentrate formulation is used, premix one part emulsifiable concentrate with two parts water. Add diluted mixture slowly through the screen into the tank. Continue agitation.
7. Continue filling the spray tank with water and add the required amount of this product near the end of the filling process.
8. If a nonionic surfactant is used, add it to the spray tank before completing the filling process.
9. Add individual formulations to the spray tank as follows: wettable powder, flowable, emulsifiable concentrate, drift reduction additive, water-soluble liquid followed by surfactant.

APPLICATION EQUIPMENT AND TECHNIQUES:
Do not apply this product through any type of irrigation system. This product may be applied to the following application equipment:

Aerial—Fixed Wing and Helicopter
Ground Broadcast Spray—Boom or boomless systems, pull-type sprayer, floaters, pick-up sprayers, spray coupes, and other ground broadcast equipment.
Hand-Held or High-Volume Spray Equipment—Knapsack and backpack sprayers, pump-up pressure sprayers, handguns, hand wands, mistblowers, lances, and other hand-held and motorized spray equipment used to direct the spray onto weed foliage.
Selective Equipment—Recirculating sprayers, shielded and hooded sprayers, wiper applicators, and sponge bars.
Injection Systems—Aerial or ground injection sprayers.
Controlled Droplet Applicator (CDA)—Hand-held or boom-mounted applications which produce a spray consisting of a narrow range of droplet sizes. 

Environmental Hazards
Do not apply directly to water, to areas where surface water is present or to intertidal areas below the mean high watermark. Do not contaminate water when cleaning equipment or disposing of equipment washwaters.

Physical or Chemical Hazards
Spray solutions of this product should be mixed, stored, and applied using only stainless steel, aluminum, fiberglass, plastic, or plastic-lined steel containers. DO NOT MIX, STORE OR APPLY THIS PRODUCT OR SPRAY SOLUTIONS OF THIS PRODUCT IN GALVANIZED STEEL OR UNLINED STEEL CONTAINERS OR SPRAY TANKS. This product or spray solutions of this product react with such containers and tanks to produce hydrogen gas which may form a highly combustible gas mixture. This gas mixture could flash or explode, causing serious personal injury if ignited by open flame, spark, welder’s torch, lighted cigarette, or another ignition source.